|
|
|
|
How do I replace the control/display on my Epilog Zing Laser?
|
|
| |
Control/Display Unit Replacement on the Epilog Zing Machine Type: Epilog Zing Laser Tools Required: Phillips screwdriver Notes: The control and display units are a single piece. They will be removed and replaced together. Included in the package that you received was an Anti-Static Strap. Wear th...
|
|
|
How do I replace the power supply on my Epilog Zing? |
|
| |
Power Supply Replacement for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Laser Tools Required: Phillips screw driver Lower the table to the bottom of the machine using the focus buttons on the display. Disconnect the machine from its power source. Remove the power cord from...
|
|
|
How do I remove my lens carriage on the Epilog Zing?
|
|
| |
Lens Carriage Removal and Installation on the Epilog Zing Laser Machine Type: Zing Engraver Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Move the X-Axis assembly to the center of the machine. Move the...
|
|
|
How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser? |
|
| |
X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1. Picture...
|
|
|
Troubleshooting the Zing Engraver
|
|
| |
Troubleshooting the Zing Engraver Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Troubleshooting.pdf...
|
|
|
How do I align the laser beam on my Epilog Zing laser? |
|
| |
...
|
|
|
How do I tension the Zing X-axis belt?
|
|
| |
How do I tension the Zing X-axis belt? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-X-Belt-Tension.pdf...
|
|
|
How do I remove and reinstall the Zing X-axis assembly? |
|
| |
How do I remove and reinstall the Zing X-axis assembly? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-X-Axis-assembly-removal-installation.pdf...
|
|
|
How do I replace the Zing X-motor?
|
|
| |
How do I replace the Zing X-motor? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-X-Motor-removal-replacement.pdf...
|
|
|
How do I replace the Zing Y-motor? |
|
| |
How do I replace the Zing Y-motor? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Y-Motor-replacement.pdf...
|
|
|
How do I replace the Zing lens carriage roller?
|
|
| |
How do I replace the Zing lens carriage roller? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Lens-Carriage-Roller-Replacement.pdf...
|
|
|
How do I align the CO2 laser in my Zing 16? |
|
| |
The instructions below show how to align the CO2 laser in the Zing 16. https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Laser-Alignment.pdf If further assistance is needed, please reach out to Epilog Tech Support by phone at 303-215-9171, or email at tech@epiloglaser.com....
|
|
|
How do I align the CO2 laser in my Zing 24?
|
|
| |
The instructions below show how to align the CO2 laser in the Zing 24. zing 24 alignment.pdf If further assistance is needed, please reach out to Epilog Tech Support by phone at 303-215-9171, or email at tech@epiloglaser.com....
|
|
|
How do I replace the Zing X-axis belt? |
|
| |
How do I replace the Zing X-axis belt? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-X-Axis-Belt-Zing.pdf...
|
|
|
How do I replace the Zing backplane board?
|
|
| |
How do I replace the Zing backplane board? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-Backplane-Board-Zing.pdf...
|