Epilog Knowledge Base - Support Center
Imagine. Design. Create.
Support Center > Knowledge base> Tagged: replace
Tag: replace
79 Articles
Orange arrow How do I replace the control board on my Mini or Helix system?

38041 views
  Control Board Replacement on the Mini and Helix Systems Machine Types: Epilog Mini 18/24, Helix Tools needed: #1 & #2 Phillips head screwdrivers Note: If you are printing through the Ethernet port it is important that you retrieve the parameter for the IP Address, Subnet Mask and Gateway fro...
Orange arrow How do I replace the flex cable on my Epilog Mini?

22264 views
  X-Axis Flex Cable Replacement on the Epilog Mini Machine Types: Epilog Mini 18/24 Tools Needed: Phillips #1 Screwdriver Turn off machine and unplug power cord. Open glass lid and locate the I-beam. Picture 1 Remove I-Beam cover by loosening the two screws on the front s...
Posted in: Epilog Mini

Orange arrow How do I replace the Helix/Mini Y-motor assembly?

5360 views
  How do I replace the Helix/Mini Y-motor assembly? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/replacing-y-motor-assembly-mini-helix.pdf...
Orange arrow How do I replace the lens on the Fusion?

10518 views
  How do I replace the lens on the Fusion? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Fusion-lens-replacement.pdf...
Orange arrow How do I replace the power supply on my Epilog Zing?

15961 views
  Power Supply Replacement for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Laser Tools Required: Phillips screw driver Lower the table to the bottom of the machine using the focus buttons on the display. Disconnect the machine from its power source. Remove the power cord from...
Posted in: Epilog Zing

Orange arrow How do I replace the laser tube in my Epilog Mini or Helix?

55240 views
  Laser Tube Replacement in the Epilog Mini and Helix Machine Types: Epilog Mini 18/24 and Helix Tools needed: Phillips head screwdriver #1 Turn off and unplug the laser system. Facing the back of the machine, remove the 9 screws using the Phillips head screwdriver on the back panel. The laser ...
Orange arrow How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser?

25693 views
  X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1. Picture...
Posted in: Epilog Zing

Orange arrow How do I replace the X-motor on the FiberMark?

3456 views
  How do I replace the X-motor on the FiberMark? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-xmotor-FiberMark.pdf...
Orange arrow How do I replace the Fusion Laser Tube?

4995 views
  How do I replace the Fusion Laser Tube? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Laser-Replacement-Fusion.pdf...
Posted in: Fusion

Orange arrow How do I replace the lens assembly on the 36EXT?

28574 views
  Replacing the Epilog Legend 36EXT Lens Assembly Although the standard 2" focal lens that comes with the EXT will work well for most projects, to achieve the optimum laser beam on special types of projects, we offer two optional focus lenses. The optional lenses on the Legend 36EXT are designed not ...
Posted in: Replacing Optics

Orange arrow How do I replace the X-Axis Read Head on my Mini?

21405 views
  X-Axis Encoder Read Head Replacement on the Mini/Helix Machine Type: Mini 18/24 Tools Required: Large #2 Phillips head screwdriver Small #3 Phillips head screwdriver 3/32 Allen Wrench Make sure the engraver is shut off. Open the plexi-glass window on the engraver. Pull the X-axis beam to t...
Posted in: Epilog Mini

Orange arrow How do I replace the x-axis belt on my Mini?

34453 views
  X-Axis Belt Replacement on the Mini Machine Type: Epilog Mini 18/24 Tools Needed: #1 and #2 Screwdriver Stapler Turn off the machine and unplug the power cord. Remove the left side panel from the engraver by removing the six screws that fix it to the body of the Mini or Helix. There ar...
Posted in: Epilog Mini
Tagged: replace, x-axis, mini, belt


Orange arrow How do I install the keyboard on my Epilog Mini?

15823 views
  Keyboard Installation on the Mini Machine Type: Epilog Mini 18/24 Tools Needed: #1 Phillips Head Screwdriver Turn machine off and unplug power cord from side of engrave. You will need to remove both the left and right hand side covers that have the hand holds. These are attached to the machi...
Posted in: Epilog Mini

Orange arrow How do I replace the Y-motor on the FiberMark?

2830 views
  How do I replace the Y-motor on the FiberMark? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/replacing-y-motor-Fibermark.pdf...
Orange arrow How do I replace the Z-motor on the FiberMark?

3018 views
  How do I replace the Z-motor on the FiberMark? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/replacing-z-motor-Fibermark.pdf...

Page: 1 of 6