|
|
|
|
How do I replace the control/display on my Epilog Zing Laser?
|
|
| |
Control/Display Unit Replacement on the Epilog Zing Machine Type: Epilog Zing Laser Tools Required: Phillips screwdriver Notes: The control and display units are a single piece. They will be removed and replaced together. Included in the package that you received was an Anti-Static Strap. Wear th...
|
|
|
How do I replace the power supply on my Epilog Zing? |
|
| |
Power Supply Replacement for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Laser Tools Required: Phillips screw driver Lower the table to the bottom of the machine using the focus buttons on the display. Disconnect the machine from its power source. Remove the power cord from...
|
|
|
How do I remove my lens carriage on the Epilog Zing?
|
|
| |
Lens Carriage Removal and Installation on the Epilog Zing Laser Machine Type: Zing Engraver Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Move the X-Axis assembly to the center of the machine. Move the...
|
|
|
How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser? |
|
| |
X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1. Picture...
|
|
|
Troubleshooting the Zing Engraver
|
|
| |
Troubleshooting the Zing Engraver Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Troubleshooting.pdf...
|
|
|
How do I align the laser beam on my Epilog Zing laser? |
|
| |
...
|
|
|
How do I replace the Y-Motor on my Zing Laser?
|
|
| |
Y-Axis Motor Replacement on the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: #1 Phillips screw driver Remove the back panel form the machine by loosening the captured screws shown in Picture 1. Note: The screws will loosen but you will not be able to remove them...
|
|
|
How do I replace the laser in my Zing Laser? |
|
| |
Machine Type: Epilog Zing 16 and 24 Lasers Tools Required: #1 Phillips screw driver Lower the table to the bottom of the machine. Turn off the machine. Disconnect the machine from its power source. Remove the four Phillips screws which secure the left hand side panel. There are three ...
|
|
|
How do I replace the lens carriage roller on my Epilog Zing?
|
|
| |
Zing Engraver Lens Carriage Roller Replacement Machine Type: Epilog Zing Laser Tools Required: Phillips screwdriver Disconnect the machine from its power source. Remove the power cord from the machine. Move the X-Axis assembly to the center of the machine. Move the lens carriage to the center o...
|
|
|
The carriage rollers in my Zing look like they are different sizes. Is something wrong? |
|
| |
Symptom: Carriage rollers are visually different in size, which may cause engraving quality issues. If the carriage rollers are left for too long, you may experience metal on metal contact once the rollers wear. Issue: Zing engravers may contain carriage rollers that have been incorrectly sized....
|
|
|
How do I replace the Zing X-axis belt?
|
|
| |
How do I replace the Zing X-axis belt? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-X-Axis-Belt-Zing.pdf...
|
|
|
How do I replace the Zing backplane board? |
|
| |
How do I replace the Zing backplane board? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-Backplane-Board-Zing.pdf...
|
|
|
How do I replace the Zing mirrors?
|
|
| |
How do I replace the Zing mirrors? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Replacing-mirrors-zing.pdf...
|
|
|
How do I check and adjust the Zing table level? |
|
| |
How do I check and adjust the Zing table level? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Checking-Table-Level-Adjustment.pdf...
|
|
|
How do I replace the Zing control and display unit?
|
|
| |
How do I replace the Zing control and display unit? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Control-Board-replacement.pdf...
|