|
|
|
|
How do I replace the x-axis rail on my Epilog Mini?
|
|
| |
X-Axis Rail Assembly Replacement on the Epilog Mini Machine Type: Epilog Mini 18/24 Tools Needed: Large Philips head screw driverSmall Philips head screw driverFlat head screw driver3/32 Allen wrenchTorx Screw Driver with 3/32 hex bit Intro: This procedure details steps to replacing th...
|
|
|
How do I replace the x-axis motor on my Epilog Mini? |
|
| |
X-Axis Motor Replacement on the Epilog Mini Machine Types: Epilog Mini 18/24 Tools Needed: #2 Phillips Head Screwdriver Turn off and unplug the laser engraver. You will need to remove the left and right sides of the engraver. To do this, you will need to remove the 6 Phillips head screws on each ...
|
|
|
How do I remove the X-Axis assembly and reinstall the new one in the Zing Laser?
|
|
| |
X-Axis Assembly Removal and Installation for the Epilog Zing Machine Type: Epilog Zing 16 and 24 Tools Required: Phillips screw driver Disconnect the machine from its power source. Remove the power cord from the machine. Loosen the captive screws shown in picture 1. Picture...
|
|
|
Troubleshooting the Zing Engraver |
|
| |
Troubleshooting the Zing Engraver Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-Troubleshooting.pdf...
|
|
|
How do I replace the X-Axis encoder strip for my Epilog Mini or Helix?
|
|
| |
X-Axis Encoder Strip Replacement for the Mini/Helix Machine Type: Epilog Mini 18/24, Helix Tools Needed: # 1 Phillips head screw driver Small Phillips head screw driver 3/32 Allen wrench Make sure power is turned off and power cord is unplugged from the wall outlet. Open up the...
|
|
|
How do I replace the X-Axis Read Head on my Mini? |
|
| |
X-Axis Encoder Read Head Replacement on the Mini/Helix Machine Type: Mini 18/24 Tools Required: Large #2 Phillips head screwdriver Small #3 Phillips head screwdriver 3/32 Allen Wrench Make sure the engraver is shut off. Open the plexi-glass window on the engraver. Pull the X-axis beam to t...
|
|
|
How do I replace the x-axis belt on my Mini?
|
|
| |
X-Axis Belt Replacement on the Mini Machine Type: Epilog Mini 18/24 Tools Needed: #1 and #2 Screwdriver Stapler Turn off the machine and unplug the power cord. Remove the left side panel from the engraver by removing the six screws that fix it to the body of the Mini or Helix. There ar...
|
|
|
How do I replace the I-beam on my Epilog Mini? |
|
| |
I-Beam Replacement on the Epilog Mini Machine Types: Epilog Mini 18/24 Tools needed: No. 2 Phillips head screwdriver No. 1 Flat head screwdriver Wire clipper Nylon tie Make sure the machine is turned off. Assuming you are facing the front of the machine, pull the right and left side panel off o...
|
|
|
How do I tension the Zing X-axis belt?
|
|
| |
How do I tension the Zing X-axis belt? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-X-Belt-Tension.pdf...
|
|
|
How do I remove and reinstall the Zing X-axis assembly? |
|
| |
How do I remove and reinstall the Zing X-axis assembly? Click the link below for instructions: https://www.epiloglaser.com/assets/downloads/tech-support/Zing-X-Axis-assembly-removal-installation.pdf...
|
|
|
How do I replace the x-axis motor in my Fusion Edge?
|
|
| |
The instructions below show how to replace the x-axis motor in the following models: Fusion Edge 12,24 & 36, Fusion Pro 24 & 36. 17 - X-Axis Motor Replacement.pdf If further assistance is needed, please reach out to Epilog Tech Support by phone at 303-215-9171, or email at tech@epil...
|
|
|
How do I replace the x-axis motor in my Fusion Pro 32 or Fusion Pro 48? |
|
| |
The instructions below detail the replacement of the x-axis motor in the Fusion Pro 32 and Fusion Pro 48. 16000 - X-Axis Motor Replacement If further assistance is needed, please reach out to Epilog Laser Tech Support by phone at 303-215-9171, or by email at tech@epiloglaser.com....
|
|
|
How do I replace the x-axis belt in my Fusion Pro 32 or Fusion Pro 48?
|
|
| |
The instructions below detail the replacement of the x-axis belt in the Fusion Pro 32 and Fusion Pro 48. 16000 - X-Axis Belt Replacement If further assistance is needed, please reach out to Epilog Laser Tech Support by phone at 303-215-9171, or by email at tech@epiloglaser.com....
|
|
|
How do I replace the x-axis drive board in my Fusion Pro 32 or Fusion Pro 48? |
|
| |
The instructions below detail the replacement of the x-axis drive board in the Fusion Pro 32 and Fusion Pro 48. 16000 - X-Axis Drive Board Replacement If further assistance is needed, please reach out to Epilog Laser Tech Support by phone at 303-215-9171, or by email at teach@epiloglaser.com...
|
|
|
How do I replace the x-axis home switch in my Fusion Pro 32 or Fusion Pro 48?
|
|
| |
The instructions below detail the replacement of the x-axis home switch in the Fusion Pro 32 and Fusion Pro 48. 16000 - X-Axis Home Switch Replacement If further assistance is needed, please reach out to Epilog Laser Tech Support by phone at 303-215-9171, or by email at tech@epiloglaser.com....
|