> Knowledge base> Category: Bravo II or XR
Search
Share
Category: Bravo II or XR
262 Articles
Orange arrow How do I disable/enable Interactive Services Dialog Detection messages in Vista / 7 / 8 / 10 ?

13518 views
  How do I disable/enable Interactive Services Dialog Detection messages in Windows Vista/7/8/10? To disable/enable Interactive Services Dialog Detection messages in Windows Vista/7/8/10, click on the Start icon and search the word “services”. Click on Services when it comes up, and fi...
Orange arrow Can I operate my Bravo with its cover open?

9768 views
  Can I operate my Bravo with its cover open? No. The cover must be closed for the robotics to move. This is a required safety feature. However, there is a way to open the lid and watch the Bravo if you need to observe the robotic movements for troubleshooting purposes. You can simply block the opt...
Orange arrow Unable to change the inner diameter or outer margin of the printed disc. (PTPublisher Mac)

7449 views
  Unable to change the inner diameter or outer margin of the printed disc. (PTPublisher Mac) 1. Make sure the image you are printing does not already have the inner diameter or outer margin built into the image. Some designers add the cropped inner circle and outer margin into the design using thei...
Orange arrow Why can't I record a 2-hour video to DVD?

8034 views
  Why can't I record a 2-hour video to DVD? The most common reason that your video will not burn to a DVD is because it is too long. When videos are originally created there are many possible bit rates that may be selected by the author. These bit rates affect the size of the video as well as the qu...
Orange arrow The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. (inhouse)

7674 views
  The arm for my Bravo / Bravo II / Bravo Pro is stuck in the up or down position. It makes a buzzing noise when I power on the unit. Bravo II This can happen if the Bravo II power is interrupted during an arm movement. Use the following procedure to correct the problem. 1. Power off the unit.2....
Orange arrow The arm and cartridges slam into the sides or move in fast jerking motions back and forth. (Bravo/BravoPro/Signature)

7085 views
  The arm and cartridges slam into the sides or move in fast jerking motions back and forth. The encoder belt may have slipped out of its track in the back of the head carriage unit or may have become unseated from the posts on either side of the unit. The printhead carriage has a sensor behind it...
Orange arrow Can I span data over multiple discs so that I can use my duplicator as a back up device? (Windows Only)

7422 views
  Can I span data over multiple discs so that I can use my duplicator as a back up device? (Windows Only) It is NOT possible to span data over the multiple discs using the Primo DVD software. You can back up data but you will need to determine where to end one set of data and begin another on multip...
Orange arrow The image is printing off center on my disc every few prints. It will print several centered and then one off center and then go back to centered again. (Bravo)

5401 views
  The image is printing off center on my disc every few prints. It will print several centered and then one off center and then go back to centered again. (Bravo) This can happen because of a dirty encoder belt on the Bravo. The encoder belt runs the entire width of the Bravo and is parallel to the...
Orange arrow What is the difference between DVD+R and DVD-R?

11056 views
  What is the difference between DVD+R and DVD-R? The practical difference between +R and -R discs is that some +R discs play on players that -R disc don't play on and vice versa. The technical differences are numerous. The main difference is that DVD+R use ADIP format to write instead of Pre-pits...
Orange arrow How many discs per cartridge can the Bravo/Bravo II print?

6810 views
  How many discs per cartridge can the Bravo/Bravo II print? This depends on many factors. However, with 100% coverage and printing an even amount of each color at the default resolution of 1200 the Bravo/Bravo II prints approximately 100 to 130 discs per cartridge. If you are not printing full cove...
Orange arrow "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed.

5446 views
  "The duplicator cover is open. Shut the top cover to continue" Received this error but the cover IS closed. The reflective sticker on the tinted cover may have come off or is out of place. If you open the lid and look where it hinges to the Bravo on the right side you should see reflective tape...
Orange arrow What is the size capacity of my DVD, Dual Layer DVD or Blu-ray disc?

22424 views
  DVD and Blu-ray manufacturers state capacity in decimal form. However, most computers read capacity in binary. The following table translates stated decimal capacity into actual binary capacity. Single layer capacity Dual/Double layer capacity Stated Capacity (GB) PTPublisher Capa...
Orange arrow I receive the error when printing from PTPublisher 'No compatible devices found, would you like to print on plain paper?' (PTPublisher)

7251 views
  I receive the error when printing from PTPublisher 'No compatible devices found, would you like to print on plain paper?' (PTPublisher) There are three possible reasons this error occurs: 1. More than one version of SureThing is installed on the computer. Check to make sure only one version o...
Orange arrow How do I prepare my unit for shipping to Primera for repair or exchange?

13565 views
  How do I prepare my unit for shipping to Primera for repair or exchange? The instructions below should be followed for each product before boxing. It is best to use the original box and foam/cardboard supports. If you do not have the box, package the product in a box large enough to leave space ...
Orange arrow Error - multiple discs have been placed in the recorder or printer but they were not - Problems picking last disc from bin - It says it is empty but it is not - After the last disc is picked, a flash

15033 views
  For BravoPro Xi, 4100 or 4200 Series Only: 1. In PTPublisher, Go to the Tools Menu - Calibrate the Disc Publisher. (For Mac: Go to the PTPublisher Menu - Calibrate Robot)2. Find the "Other Calibrations" section at the bottom.3. If the error occurred after the disc was placed in the printer, click ...

Page: 1 of 18
©2024 Primera   |   powered by LiveHelpNow Help Desk Software
 Total articles: 640 | Total views: 4203969